{"product_id":"simpact™-60a","title":"Simpact™ 60A Special Order","description":"\u003cp\u003e\u003cstrong\u003eSimpact™ 60A\u003c\/strong\u003e urethane is a low odor, fast-setting urethane elastomer which offers very high tear strength, impact resistance and wear resistance. \u003cstrong\u003eSimpact™ urethanes are phthalate free, mercury free and MOCA free\u003c\/strong\u003e. \u003cstrong\u003eSimpact™\u003c\/strong\u003e urethanes pour easily. \u003cstrong\u003eWorking time is 4 minutes, handling time is 2 hours and full cure time is 48 hours at room temperature.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eCured rubber has exceptional performance characteristics and dimensional stability.\u003cstrong\u003e Simpact™\u003c\/strong\u003e urethanes can be colored with \u003cstrong\u003eSO-Strong™\u003c\/strong\u003e, \u003cstrong\u003eUVO™\u003c\/strong\u003e or \u003cstrong\u003eIgnite™\u003c\/strong\u003e colorants. \u003cstrong\u003eSimpact™\u003c\/strong\u003e urethanes are suitable for making impact resistant props, prototypes and display pieces.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eThis material may congeal if exposed to cold temperatures. To reconstitute, Part A \u0026amp; B must be heated to 90°F (33°C) then thoroughly mixed to an even consistency.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cimg alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0780\/7539\/6411\/files\/simpactspecs.png?v=1732635750\"\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch2\u003eInstructions\u003c\/h2\u003e\n\u003cp\u003eThese products have a limited shelf life and should be used as soon as possible. This material should be stored and used at room temperature (73°F\/23°C). This material is moisture sensitive, so relative humidity should be below 50%. Wear safety glasses, long sleeves and rubber gloves to minimize contamination risk. Room size ventilation is necessary.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cem\u003eApplying A Release Agent\u003c\/em\u003e \u003c\/strong\u003e- A release agent is necessary to facilitate demolding when casting into or over most surfaces. Use a release agent made specifically for mold making (\u003cstrong\u003eUniversal™ Mold Release\u003c\/strong\u003e or Mann’s \u003cstrong\u003eEase Release™ 200\u003c\/strong\u003e available from Smooth-On or your Smooth-On distributor). A liberal coat of release agent should be applied onto all surfaces that will contact the material.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIMPORTANT:\u003c\/strong\u003e To ensure thorough coverage, apply release and brush with a soft brush over all surfaces. Follow with a light mist coating and let the release agent dry for 30 minutes.\u003c\/p\u003e\n\u003cp\u003eSmooth-On silicone rubber molds usually do not require a release agent unless casting silicone into the mold. Applying a release agent will prolong the life of the mold.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cem\u003eSelecting A Mold Rubber\u003c\/em\u003e - \u003c\/strong\u003ePour into a urethane rubber mold (release agent required) or a silicone rubber mold. To prevent cure inhibition, post-cure newly made tin silicone molds for 8 hours at 60°C\/150°F and let cool prior to casting. If you are unsure about surface compatibility, a trial casting should be made.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eBecause no two applications are quite the same, a small test application to determine suitability for your project is recommended if performance of this material is in question.\u003c\/strong\u003e\u003c\/p\u003e\n\u003chr\u003e\n\u003cp\u003e\u003cstrong\u003eMEASURING \u0026amp; MIXING...\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eLiquid urethanes are \u003cstrong\u003emoisture sensitive \u003c\/strong\u003eand will absorb atmospheric moisture resulting in bubbles in the cured rubber. Mixing tools and containers should be clean and made of metal or plastic.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eShelf life of product is drastically reduced after opening.\u003c\/strong\u003e Immediately replacing the lids on the containers after dispensing product will prolong the shelf life of the unused product. \u003cstrong\u003eXTEND-IT™ Dry Gas Blanket\u003c\/strong\u003e (available from Smooth-On) will prolong the shelf life of unused liquid urethane products.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIMPORTANT: Pre Mix the Part B before using every time.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cem\u003eHand Mixing \u003c\/em\u003e-\u003c\/strong\u003e After weighing and dispensing the required amounts of Parts A and B into mixing container, mix thoroughly for at least 60 seconds making sure that you scrape the sides and bottom of the mixing container several times. Pour entire quantity into a new, clean mixing container and mix again as directed above.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cem\u003eMechanical Mixing\u003c\/em\u003e -\u003c\/strong\u003e drill mix using a Turbine mixer or equal for 30 seconds followed by careful hand mixing for 30 seconds as directed above. Then, pour entire quantity into a new, clean mixing container and repeat mixing procedure.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cem\u003eBe Aware \u003c\/em\u003e-\u003c\/strong\u003e material pot life is 4 minutes at 73°F\/23°C. Pot life at elevated temperatures will be less. Do not delay between mixing and pouring.\u003c\/p\u003e\n\u003cp\u003eAlthough this product is formulated to minimize air bubbles when cured, vacuum degassing will further reduce entrapped air. A pressure casting technique using a pressure chamber can yield totally bubble free castings. Contact Smooth-On or your distributor for information about vacuum degassing or pressure casting.\u003c\/p\u003e\n\u003chr\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cem\u003ePouring \u003c\/em\u003e-\u003c\/strong\u003e For best results, pour your mixture in a single spot at the lowest point of the containment field. Let the rubber seek its level A uniform flow will help minimize entrapped air.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cem\u003eCuring \u003c\/em\u003e- \u003c\/strong\u003eAllow casting to cure for at least 2 hours at room temperature (73°F\/23°C) before demolding. Do not cure rubber in temperatures less than 65°F\/18°C. This material will reach full cure in 48 hours at 73°F\/23°C.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cem\u003eHeat Curing\u003c\/em\u003e -\u003c\/strong\u003e Allow casting to cure for 24 hours at room temperature (73°F\/23°C). Heat cure casting at 140°F\/60°C for 6 hours. Allow casting to cool to room temperature before handling.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cem\u003ePerformance \u0026amp; Storage\u003c\/em\u003e -\u003c\/strong\u003e Fully cured rubber is tough, durable and will perform if properly used and stored. The physical life of the rubber depends on how you use it. Contact Smooth-On directly with questions about this material relative to your application.\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.smooth-on.com\/tb\/files\/SIMPACT_SERIES_TB.pdf\" title=\"TDS\" rel=\"noopener\" target=\"_blank\"\u003eTDS\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.smooth-on.com\/msds\/files\/Simpact_60A_85A.pdf\" title=\"SDS\" rel=\"noopener\" target=\"_blank\"\u003eSDS\u003c\/a\u003e\u003c\/p\u003e","brand":"Smooth-On","offers":[{"title":"Trial Kit (1.94 lbs. \/ 0.88 kg.)","offer_id":49719990419771,"sku":"57344","price":29.99,"currency_code":"USD","in_stock":false},{"title":"2 Gallon Kit (15.5 lbs. \/ 7.03 kg.)","offer_id":49719990452539,"sku":"57361","price":167.99,"currency_code":"USD","in_stock":false},{"title":"10 Gallon Kit (77.5 lbs. \/ 35.15 kg.)","offer_id":49719990485307,"sku":"57371","price":671.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0780\/7539\/6411\/files\/Simpact-60A-combo-1400x1050.jpg?v=1754777093","url":"https:\/\/maacaffestore.com\/es\/products\/simpact%e2%84%a2-60a","provider":"The Compleat Sculptor, Inc","version":"1.0","type":"link"}