{"product_id":"epoxacoat-grey","title":"EpoxAcoat™ GREY","description":"\u003cp\u003e\u003cstrong\u003e\u003cimg src=\"https:\/\/cdn.shoplightspeed.com\/shops\/606431\/files\/50275647\/epoxacoatchart.png\" alt=\"\" width=\"446\" height=\"733\"\u003e\u003c\/strong\u003e\u003c\/p\u003e\r\n\u003cp\u003e\u003cstrong\u003e\u003ca href=\"https:\/\/www.smooth-on.com\/tb\/files\/EPOXACOAT_SERIES_TB.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTechnical Data \u0026amp; Instructions\u003c\/a\u003e\u003c\/strong\u003e\u003c\/p\u003e\r\n\u003cp\u003e\u003cstrong\u003eEpoxAcoat™ RED, GREY, WHITE and NEUTRAL\u003c\/strong\u003e are thixotropic epoxy gel coats which are widely used for hand laminating and tooling applications. They are tough and strong surface coat resins which cure at room temperature and offer exceptional abrasion resistance.\u003cstrong\u003e EpoxAcoat™ NEUTRAL\u003c\/strong\u003e is formulated “color neutral” specifically for adding color pigments and fillers. For high temperature applications (to 284°F \/ 140°C) use \u003cstrong\u003eEpoxAcoat HT™\u003c\/strong\u003e (see separate technical bulletin).\u003c\/p\u003e\r\n\u003cp\u003eFeatures\u003c\/p\u003e\r\n\u003cp\u003e\u003cstrong\u003eEpoxAcoat™ Surface Coat Epoxies\u003c\/strong\u003e are easy to use, wet out well over a variety of surfaces and will coat vertical surfaces without sagging. After the epoxy becomes “tacky-hard” at room temperature, fiberglass cloth is laminated behind the surface coat using \u003cstrong\u003eFree Form™ AIR\u003c\/strong\u003e putty or \u003cstrong\u003eEpoxAmite™\u003c\/strong\u003e Laminating Epoxy to produce strong, lightweight tools that have excellent dimensional stability and surface finish. Cured surface machines precisely without chipping. Applications include precision tooling, master and pattern making, core boxes and fixtures.\u003c\/p\u003e\r\n\u003cp\u003eInstructions\u003c\/p\u003e\r\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003ePreparation\u003c\/strong\u003e\u003c\/em\u003e – Avoid breathing fumes - use in a well ventilated area at minimum. NIOSH approved respirator is recommended. Wear safety glasses, long sleeves and rubber gloves to minimize skin contact. This material has a high exotherm (generates heat). Do not mix components in glass or foam containers.\u003cbr\u003e\u003cbr\u003eMaterials should be stored and used in a room temperature environment (73°F\/23°C). Elevated temperatures will reduce Pot Life. \u003cstrong\u003eEpoxAcoat™ GREY Resin\u003c\/strong\u003e and \u003cstrong\u003ePART B Hardener\u003c\/strong\u003e must be properly measured and thoroughly mixed to achieve full, high-strength, solidcure properties. \u003cstrong\u003eBecause no two applications are quite the same, a small test application to determine suitability for your project is recommended if performance of this material is in question.\u003c\/strong\u003e\u003cbr\u003e\u003cbr\u003e\u003cem\u003e\u003cstrong\u003eApplying A Release Agent\u003c\/strong\u003e \u003c\/em\u003e– For releasing epoxy from nonporous surfaces such as resin, metal, glass etc., use \u003cstrong\u003eEase Release™ 200 or 205 \u003c\/strong\u003e(available from Smooth-On) to prevent adhesion.\u003c\/p\u003e\r\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eMeasuring \/ Dispensing\u003c\/strong\u003e \u003c\/em\u003e– Accurate ratio measurements by volume or weight are required for the material to cure properly and develop full physical properties. Dispense Parts A and B proper proportions into clean plastic, metal or wax-free paper containers.\u003cbr\u003e\u003cbr\u003e\u003cem\u003e\u003cstrong\u003eAdding Color\u003c\/strong\u003e \u003c\/em\u003e- The \u003cstrong\u003eEpoxAcoat™\u003c\/strong\u003e Epoxy Surface Coat System can be colored with \u003cstrong\u003eUVO™\u003c\/strong\u003e color tints (from Smooth-On). Pre-mix tint with Part A thoroughly and then add Part B.\u003c\/p\u003e\r\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eMixing\u003c\/strong\u003e\u003c\/em\u003e – Be sure mixing utensils are clean and free of any potential contaminants such as dirt, dust or grease. Mix Parts A and B thoroughly for at least 3 minutes with a square edged mixing stick. Be aggressive and scrape sides and bottom of mixing container several times. Use the square edge of mixing stick to bring material off of the sides of container and blend. \u003cstrong\u003eIf using a drill mixer\u003c\/strong\u003e, follow with hand mixing as directed above to ensure thorough mixing. \u003cstrong\u003eNOTE\u003c\/strong\u003e: Pot life can be extended by pouring mixture into a shallow pan, reducing its mass.\u003cbr\u003e\u003cbr\u003e\u003cem\u003e\u003cstrong\u003eAdding Fillers\u003c\/strong\u003e\u003c\/em\u003e - A variety of dry fillers can be added. Pre-mix dry filler with Part A before adding Part B.\u003cbr\u003e\u003cstrong\u003eImportant\u003c\/strong\u003e - Mixed \u003cstrong\u003eEpoxAcoat™ Resin\u003c\/strong\u003e with \u003cstrong\u003eEpoxAcoat™ PART B Hardener \u003c\/strong\u003eis exothermic, meaning it generates heat. A concentrated mass of mixed epoxy in a confined area such as a mixing container can generate enough heat to melt a plastic cup, burn skin or ignite combustible materials if left to stand for its full Pot Life. Do not use foam or glass mixing containers or apply sections thicker than 1\/8” (0.32 cm). If a batch of mixed epoxy begins to exotherm, move it to an open air environment.\u003c\/p\u003e\r\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eApplying\u003c\/strong\u003e\u003c\/em\u003e – You will apply two thin layers of \u003cstrong\u003eEpoxAcoat™\u003c\/strong\u003e using a disposable chip brush. After epoxy is mixed, you must work quickly so that the mass in your mixing container does not set up prematurely. NOTE: Pot life can be extended by pouring mixture into a shallow pan, reducing its mass.\u003cbr\u003eAfter applying 1 thin layer of epoxy, let partially cure for 1 hour until “tacky hard”. Apply a second thin layer and again partially cure for 1 hour until “tacky hard”.\u003cbr\u003eNext, \u003cstrong\u003eFree Form™ AIR \u003c\/strong\u003eEpoxy Putty or \u003cstrong\u003eEpoxAmite™ 100\u003c\/strong\u003e Laminating Resin and reinforcement cloth may be laminated over the surface coat. See \u003cstrong\u003eEpoxAmite™ 100\u003c\/strong\u003e Laminating Resin Technical Bulletin for details.\u003c\/p\u003e\r\n\u003cp\u003e\u003cstrong\u003e\u003cem\u003eCure Time -\u003c\/em\u003e\u003c\/strong\u003e Refer to specified Cure Times in Handling Properties at 73°F \/ 23°C depending on mass. Cured material will be hard and unable to penetrate with a finger nail. Cured epoxy can now be dry sanded. \u003cstrong\u003eIf machining or sanding, wear NIOSH approved mask to prevent inhalation of particles.\u003c\/strong\u003e\u003cbr\u003e\u003cbr\u003e\u003cem\u003e\u003cstrong\u003eHeat Curing\u003c\/strong\u003e\u003c\/em\u003e - This product will cure at room temperature and does not require heat. Cure time can be reduced by applying mild heat. The higher the curing temperature is, the higher the resulting Heat Deflection Temperature. With a higher temperature cure, a service temperature of 138°F \/ 59°C can be attained. Allow epoxy to cure for 30 minutes and then cure for 1 hour at 200°F \/ 93°C. Allow casting to cool to room temperature before handling.\u003cbr\u003e\u003cbr\u003e\u003cem\u003e\u003cstrong\u003ePainting\u003c\/strong\u003e\u003c\/em\u003e – Cured \u003cstrong\u003eEpoxAcoat™\u003c\/strong\u003e can be painted and \/ or primed and then painted with acrylic enamel paints. Let paint fully dry before putting part into service.\u003cbr\u003e\u003cbr\u003e\u003cem\u003e\u003cstrong\u003eRemoving Epoxy\u003c\/strong\u003e \u003c\/em\u003e\u003cstrong\u003e\u003cem\u003e– Uncured \/ Non-curing epoxy\u003c\/em\u003e \u003c\/strong\u003e- Scrape as much material as possible from the surface using a scraper. Clean the residue with \u003cstrong\u003eE-POXEE KLEENER™ \u003c\/strong\u003eavailable from Smooth-On, lacquer thinner, acetone or alcohol. Follow safety warnings pertaining to solvents and provide adequate ventilation.\u003c\/p\u003e\r\n\u003cp\u003e\u003ca href=\"https:\/\/www.smooth-on.com\/msds\/files\/1053A_1_1053B_2.pdf\" target=\"_blank\" rel=\"noopener\"\u003eSDS\u003c\/a\u003e\u003c\/p\u003e","brand":"Smooth-On","offers":[{"title":"Trial Kit (2.31 lbs. \/ 1.05 kg.)","offer_id":48015624241467,"sku":"17642","price":39.99,"currency_code":"USD","in_stock":false},{"title":"Gallon Kit (11.5 lbs. \/ 5.22 kg.)","offer_id":48015624208699,"sku":"17661","price":128.99,"currency_code":"USD","in_stock":false},{"title":"5 Gallon Kit (57.5 lbs. \/ 26.08 kg.)","offer_id":48015624175931,"sku":"17671","price":518.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0780\/7539\/6411\/files\/epoxacoat-grey-combo-533x400.jpg?v=1713390556","url":"https:\/\/maacaffestore.com\/products\/epoxacoat-grey","provider":"The Compleat Sculptor, Inc","version":"1.0","type":"link"}