{"product_id":"epoxamite-laminating-system","title":"EpoxAmite™ 100 Laminating System","description":"\u003cp\u003e\u003cimg height=\"656\" width=\"685\" alt=\"\" src=\"https:\/\/cdn.shoplightspeed.com\/shops\/606431\/files\/50274466\/epoxamitechart.png\"\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca rel=\"noopener\" href=\"https:\/\/www.smooth-on.com\/tb\/files\/Epoxamite_TB.PDF\" target=\"_blank\"\u003eTechnical Data \u0026amp; Instructions\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003ePLEASE NOTE 5 GALLON OPTIONS ARE SOLD BY INDIVIDUAL COMPONENT.  PLEASE SELECT THE 100 PART A, THEN GO BACK AND SELECT YOUR DESIRED PART B\u003c\/p\u003e\n\u003cp\u003eEpoxAmite™ 100 Epoxy Laminating System is an easy-to-use liquid epoxy system formulated for a wide variety of fabrication\u003cbr\u003eapplications. EpoxAmite™ 100 Laminating System is unfilled, low in viscosity, odorless and cures at room temperature. Cured epoxy\u003cbr\u003edisplays exceptional physical and performance properties. It can be sanded, shaped, machined, drilled, tapped and painted.\u003c\/p\u003e\n\u003cp\u003eEpoxAmite™ 100 Laminating System can be used with reinforcements such as S-Glass, E-Glass, Kevlar and Carbon fibers for lay-up\u003cbr\u003eapplications or composite parts. EpoxAmite™ 100 Resin can also be mixed with fillers such as fumed silica for gel coat applications.\u003cbr\u003eUrefil™ 3, Urefil™ 7 and other fillers can be added for fairing, filleting or bonding applications.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAdvantages Include:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eConvenient Mix Ratios\u003c\/li\u003e\n\u003cli\u003eEasy-to-Use\u003c\/li\u003e\n\u003cli\u003eExcellent Moisture Resistance\u003c\/li\u003e\n\u003cli\u003eLow Viscosity\u003c\/li\u003e\n\u003cli\u003eNon-blush Formula\u003c\/li\u003e\n\u003cli\u003eEasy-to-Mix \u0026amp; Apply\u003c\/li\u003e\n\u003cli\u003eExceptional Physical \u0026amp; Performance Properties\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cem\u003ePreparation\u003c\/em\u003e –\u003c\/strong\u003e Avoid breathing fumes - use in a well ventilated area at minimum. NIOSH approved respirator is recommended. Wear safety glasses, long sleeves and rubber gloves to minimize skin contact. This material has a high exotherm (generates heat). Do not mix components in glass or foam containers. Mixing containers should have straight sides and a flat bottom. Mixing sticks should be flat and stiff with defined edges for scraping the sides and bottom of your mixing container.\u003c\/p\u003e\n\u003cp\u003eMaterials should be stored and used in a room temperature environment (73°F\/23°C). Elevated temperatures will reduce Pot Life. \u003cstrong\u003eEpoxAmite™ 100\u003c\/strong\u003e Resin and \u003cstrong\u003e101, 102, 103 Hardener\u003c\/strong\u003e must be properly measured and thoroughly mixed to achieve full, high-strength, solid-cure properties. \u003cstrong\u003eBecause no two applications are quite the same, a small test application to determine suitability for your project is recommended if performance of this material is in question.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cem\u003eApplying A Release Agent \u003c\/em\u003e– \u003c\/strong\u003eFor releasing epoxy from non-porous surfaces such as resin, metal, glass etc., use \u003cstrong\u003eEase Release™ 200 or 205\u003c\/strong\u003e (available from Smooth-On) to prevent adhesion.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cem\u003eMeasuring \/ Dispensing\u003c\/em\u003e – \u003c\/strong\u003eAccurate ratio measurements by volume or weight are required for the material to cure properly and develop full physical properties. Stir Part A and Part B thoroughly before dispensing. Refer to specified Mix Ratios in Handling Properties for proper measurements. Dispense Parts A and B proper proportions into clean plastic, metal or wax-free paper containers.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cem\u003eAdding Color \u003c\/em\u003e-\u003c\/strong\u003e \u003cstrong\u003eEpoxAmite™ 100\u003c\/strong\u003e Epoxy Laminating System can be colored with \u003cstrong\u003eUVO™\u003c\/strong\u003e or \u003cstrong\u003eIGNITE™\u003c\/strong\u003e colorants. Pre-mix color with Part A thoroughly and then add Part B.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cem\u003eMixing \u003c\/em\u003e–\u003c\/strong\u003e Be sure mixing utensils are clean and free of any potential contaminants such as dirt, dust or grease. Mix Parts A and B thoroughly for at least 3 minutes with a square edged mixing stick. Be aggressive and scrape sides and bottom of mixing container several times. Use the square edge of mixing stick to bring material off of the sides of container and blend. \u003cstrong\u003eIf using a drill mixer, \u003c\/strong\u003efollow with hand mixing as directed above to ensure thorough mixing. \u003cstrong\u003eNOTE:\u003c\/strong\u003e If mixture is to be used for coating, pour into a roller pan to extend Pot Life.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cem\u003eAdding Fillers\u003c\/em\u003e -\u003c\/strong\u003e A variety of dry fillers can be added. Pre-mix dry filler with Part A before adding Part B.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cem\u003eLowering Viscosity\u003c\/em\u003e - Epic™ Epoxy Thinner\u003c\/strong\u003e is a clear, water-like liquid that will lower the viscosity of some Smooth-On casting and laminating epoxies. \u003cstrong\u003eEpic™\u003c\/strong\u003e is not a solvent and can be added in different proportions to improve flow-ability to make it easier to mix and pour or laminate. \u003cstrong\u003eEpic™ \u003c\/strong\u003ewill also aid in reducing bubble entrapment.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cem\u003eIncreasing Flexibility\u003c\/em\u003e -\u003c\/strong\u003e \u003cstrong\u003eFlexer™ Epoxy Flexibilizer \u003c\/strong\u003eis a clear, low viscosity liquid additive that will lower the durometer (Shore hardness) of some Smooth-On casting and laminating epoxies. When added to the epoxy system in the proper proportion, the cured epoxy will be softer and, in some cases, can be made semi-rigid. See the \u003cstrong\u003eFlexer™ \u003c\/strong\u003eTechnical Bulletin for more information.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eImportant -\u003c\/strong\u003e Mixed \u003cstrong\u003eEpoxAmite™ 100\u003c\/strong\u003e Resin with \u003cstrong\u003eEpoxAmite™ 101, 102, 103 Hardener\u003c\/strong\u003e is exothermic, meaning it generates heat. A concentrated mass of mixed epoxy in a confined area such as a mixing container can generate enough heat to melt a plastic cup, burn skin or ignite combustible materials if left to stand for its full Pot Life. Do not use foam or glass mixing containers or pour sections thicker than 1\/8” (0.32 cm). If a batch of mixed epoxy begins to exotherm, move it to an open air environment.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cem\u003eApplying\u003c\/em\u003e – \u003c\/strong\u003eMixed \u003cstrong\u003eEpoxAmite™ 100\u003c\/strong\u003e is initially a low viscosity liquid that can be poured up to 1\/8” (0.32 cm) thickness.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cem\u003eLaminating - \u003c\/em\u003e\u003c\/strong\u003ecut the bristles of a chip brush 30% for better control. After epoxy is mixed, you must work quickly to apply multiple layers. Brush an initial gel coat of epoxy over surface. Apply reinforcement fabric evenly into gel coat. Using brush, gently use stippling motion to work fabric into epoxy. Ensure fabric ply is saturated. Plastic polyethylene spreaders may also be used.\u003c\/p\u003e\n\u003cp\u003eAlternate additional thin layers of epoxy and fabric using above application method. Add additional epoxy as needed to wet out subsequent layers. Repeat as necessary until desired thickness is attained. After final layer of fabric is applied, use lamination roller to evenly distribute epoxy and reduce air bubbles. Be mindful of your Thin Film Working Time.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cem\u003eCure Time -\u003c\/em\u003e \u003c\/strong\u003eRefer to specified Cure Times in Handling Properties at room temperature depending on mass. Cured material will be hard and unable to penetrate with a finger nail. Cured epoxy can now be dry sanded.\u003cem\u003e\u003cstrong\u003e If machining or sanding, wear NIOSH approved mask to prevent inhalation of particles. \u003c\/strong\u003e\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cem\u003eHeat Curing\u003c\/em\u003e - \u003c\/strong\u003eThis product will cure at room temperature and does not require heat. Cure time can be reduced by applying mild heat. The higher the curing temperature is, the higher the resulting Heat Deflection Temperature. With a higher temperature cure, a service temperature of 138°F \/ 59°C can be attained. Allow epoxy to cure for 30 minutes and then cure for 1 hour at 200°F \/ 93°C. Allow casting to cool to room temperature before handling.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cem\u003ePainting\u003c\/em\u003e – \u003c\/strong\u003eCured \u003cstrong\u003eEpoxAmite™ 100\u003c\/strong\u003e Laminating System can be painted and \/ or primed and then painted with acrylic enamel paints. Let paint fully dry before putting part into service.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cem\u003eRemoving Epoxy – Uncured \/ Non-curing epoxy -\u003c\/em\u003e \u003c\/strong\u003eScrape as much material as possible from the surface using a scraper. Clean the residue with \u003cstrong\u003eE-POX-EE KLEENER™\u003c\/strong\u003e available from Smooth-On, lacquer thinner, acetone or alcohol. Follow safety warnings pertaining to solvents and provide adequate ventilation.\u003c\/p\u003e\n\u003cp\u003e\u003ca rel=\"noopener\" href=\"https:\/\/www.smooth-on.com\/msds\/files\/EpoxAmite_101_Comp.pdf\" target=\"_blank\"\u003e101 SDS\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca rel=\"noopener\" href=\"https:\/\/www.smooth-on.com\/msds\/files\/EpoxAmite_102_Comp.pdf\" target=\"_blank\"\u003e102 SDS\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca rel=\"noopener\" href=\"https:\/\/www.smooth-on.com\/msds\/files\/EpoxAmite_103_Comp.pdf\" target=\"_blank\"\u003e103 SDS\u003c\/a\u003e\u003c\/p\u003e","brand":"Smooth-On","offers":[{"title":"100 Part A 5 Gallon (36 lbs. \/ 16.33 kg.)","offer_id":48015623487803,"sku":"03070A","price":274.99,"currency_code":"USD","in_stock":false},{"title":"101 Fast Trial Kit (2.5 lbs. \/ 1.13 kg.)","offer_id":48015623586107,"sku":"03042","price":45.99,"currency_code":"USD","in_stock":true},{"title":"101 Fast Gallon Kit (10 lbs. \/ 4.54 kg.)","offer_id":48015623520571,"sku":"03061","price":124.99,"currency_code":"USD","in_stock":false},{"title":"101 Fast Part B for 5 Gallon (9 lbs. \/ 4.08 kg.)","offer_id":48015623553339,"sku":"03070B","price":219.99,"currency_code":"USD","in_stock":true},{"title":"102 Medium Trial Kit (2.6 lbs. \/ 1.18 kg.)","offer_id":48015623684411,"sku":"03142","price":46.99,"currency_code":"USD","in_stock":true},{"title":"102 Medium Gallon Kit (10.3 lbs. \/ 4.67 kg.)","offer_id":48015623618875,"sku":"03161","price":127.99,"currency_code":"USD","in_stock":true},{"title":"102 Medium Part B for 5 Gallon (10.5 lbs. \/ 4.76 kg.)","offer_id":48015623651643,"sku":"03170B","price":209.99,"currency_code":"USD","in_stock":true},{"title":"103 Slow Trial Kit (2.57 lbs. \/ 1.17 kg.)","offer_id":48015623782715,"sku":"03242","price":46.99,"currency_code":"USD","in_stock":true},{"title":"103 Slow Gallon Kit (10.27 lbs. \/ 4.66 kg.)","offer_id":48015623717179,"sku":"03261","price":127.99,"currency_code":"USD","in_stock":true},{"title":"103 Slow Part B for 5 Gallon (10.2 lbs. \/ 4.63 kg.)","offer_id":48015623749947,"sku":"03270B","price":199.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0780\/7539\/6411\/files\/epoxamitesupercombo.jpg?v=1710987221","url":"https:\/\/maacaffestore.com\/products\/epoxamite-laminating-system","provider":"The Compleat Sculptor, Inc","version":"1.0","type":"link"}