{"product_id":"epsilon-101-fast-hardener","title":"EPSILON™ + 101 FAST Hardener","description":"\u003cp\u003e\u003cstrong\u003eEPSILON™\u003c\/strong\u003e is a thixotropic epoxy coating that self thickens for brushing onto a variety of surfaces without sagging. Parts A and B mix together easily, and the mixture wets out uniformly. This product is not sensitive to moisture or humidity. \u003cstrong\u003eEPSILON™\u003c\/strong\u003e cures at room temperature to an impact resistant plastic which exhibits good compressive and flexural strength.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eEPSILON™\u003c\/strong\u003e is color neutral, and cured material can be easily sanded, primed and painted. \u003cstrong\u003eEPSILON™\u003c\/strong\u003e is suitable for use as a protective, impact resistant coating for EPS or polyurethane foam. It can also be applied to plaster, concrete, wood and fabrics. This product is not sensitive to moisture or humidity and \u003cstrong\u003econtains no VOC’s.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cimg src=\"https:\/\/cdn.shoplightspeed.com\/shops\/606431\/files\/52739265\/epsilonfastspecs.png\" alt=\"\" width=\"510\" height=\"635\"\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eInstructions\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003ePreparation\u003c\/strong\u003e\u003c\/em\u003e – Avoid breathing fumes - use in a well ventilated area at minimum. NIOSH approved respirator is recommended. Wear safety glasses, long sleeves and rubber gloves to minimize skin contact. This material has a high exotherm (generates heat). Do not mix components in glass or foam containers.\u003c\/p\u003e\n\u003cp\u003eMaterials should be stored and used in a room temperature environment (73°F\/23°C). Elevated temperatures will reduce Pot Life. \u003cstrong\u003eEPSILON™\u003c\/strong\u003e Part A resin and Part B Hardener must be properly measured and thoroughly mixed to achieve full, high-strength, solid-cure properties.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eApplying a Release Agent\u003c\/strong\u003e\u003c\/em\u003e – For releasing epoxy from non-porous surfaces such as resin, metal, glass etc., use \u003cstrong\u003eEase Release™ 200 or 205\u003c\/strong\u003e (available from Smooth-On) to prevent adhesion.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eMeasuring and Dispensing\u003c\/strong\u003e\u003c\/em\u003e – Accurate ratio measurements by weight are required for the material to cure properly and develop full physical properties. Dispense proper proportions of parts A and B into clean plastic, metal or wax-free paper containers.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eMixing\u003c\/strong\u003e\u003c\/em\u003e –\u003cstrong\u003e Do not use foam or glass mixing containers.\u003c\/strong\u003e Be sure mixing utensils are clean and free of any potential contaminants such as dirt, dust or grease. Mix Parts A and B thoroughly for at least 3 minutes with a square edged mixing stick. Be aggressive and scrape sides and bottom of mixing container several times. Use the square edge of mixing stick to bring material off of the sides of container and blend. \u003cstrong\u003eIf using a drill mixer,\u003c\/strong\u003e follow with hand mixing as directed above to ensure thorough mixing. \u003cstrong\u003eNOTE: \u003c\/strong\u003ePot life can be extended by pouring mixture into a shallow pan, reducing its mass.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eImportant\u003c\/strong\u003e -\u003cstrong\u003e Mixed EPSILON™ Resin with EpoxAmite™ PART B Hardener is exothermic, meaning it generates heat. A concentrated mass of mixed epoxy in a confined area such as a mixing container can generate enough heat to melt a plastic cup, burn skin or ignite combustible materials if left to stand for its full Pot Life. If a batch of mixed epoxy begins to exotherm, move it to an open air environment.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eAdding Color \u003c\/strong\u003e\u003c\/em\u003e- \u003cstrong\u003eEPSILON™\u003c\/strong\u003e Epoxy Surface Coat System can be colored with \u003cstrong\u003eUVO™ \u003c\/strong\u003eor \u003cstrong\u003eIGNITE™\u003c\/strong\u003e colorants (from Smooth-On). Pre-mix colorant with Part A thoroughly and then add Part B.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eAdding Fillers\u003c\/strong\u003e \u003c\/em\u003e- A variety of dry fillers can be added. Pre-mix dry filler with Part A before adding Part B.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eExtending Working Time\u003c\/strong\u003e\u003c\/em\u003e – mixed material in a deep mixing cup or bucket will set up quickly due to concentration of the liquid mass. Pour mixture into a flat (shallow) metal cookie sheet or baking pan and dispense product from there. Working time will be extended.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eApply In Thin Layers\u003c\/strong\u003e\u003c\/em\u003e - two thin layers of \u003cstrong\u003eEPSILON™\u003c\/strong\u003e are recommended for a smooth, uniform coating. Using chip brush or roller, apply 1st thin layer to surface and let epoxy partially cure until “tacky hard”. Apply 2nd thin layer. Allow both layers to fully cure. \u003cstrong\u003eDo not apply epoxy thicker than 1\/8” (0.32 cm) per layer as this may cause sagging and result in an uneven cured coating. \u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eWhen coating areas of fine detail, using successive thin layers of \u003cstrong\u003eEPSILON™\u003c\/strong\u003e will allow a protective layer of material to be built up without obscuring the detail of the original surface.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eCure Time -\u003c\/strong\u003e \u003c\/em\u003eRefer to the specified \u003cem\u003e\u003cstrong\u003e“Cure Times”\u003c\/strong\u003e\u003c\/em\u003e in the \u003cem\u003e\u003cstrong\u003e“Material Properties”\u003c\/strong\u003e\u003c\/em\u003e section on front of this Technical Bulletin. Fully cured material will be hard and unable to penetrate with a finger nail. Cured epoxy can now be dry sanded.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIf machining or sanding, wear NIOSH approved mask to prevent inhalation of particles.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eCuring\u003c\/strong\u003e \u003c\/em\u003e- This product will cure at room temperature (73°F\/23°C) and does not require heat.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003ePainting\u003c\/strong\u003e\u003c\/em\u003e – \u003cstrong\u003eEPSILON™\u003c\/strong\u003e can be painted and\/or primed and then painted with acrylic enamel paints. Let paint fully dry before putting part into service. For best results, lightly sand surface prior to painting.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eRemoving Epoxy\u003c\/strong\u003e\u003c\/em\u003e – \u003cstrong\u003eUncured \/ Non-curing epoxy: \u003c\/strong\u003eScrape as much material as possible from the surface using a scraper. Clean the residue with\u003cstrong\u003e E-POX-EE KLEENER™ \u003c\/strong\u003eavailable from Smooth-On, lacquer thinner, acetone or alcohol. Follow safety warnings pertaining to solvents and provide adequate ventilation.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eBecause no two applications are quite the same, a small test application to determine suitability for your project is recommended if performance of this material is in question.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003ca href=\"https:\/\/www.smooth-on.com\/msds\/files\/Epsilon.pdf\" rel=\"noopener\" target=\"_blank\"\u003eSDS\u003c\/a\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003ca href=\"https:\/\/www.smooth-on.com\/tb\/files\/EPSILON_TB.pdf\" rel=\"noopener\" target=\"_blank\"\u003eTDS\u003c\/a\u003e\u003c\/strong\u003e\u003c\/p\u003e","brand":"Smooth-On","offers":[{"title":"Trial Kit (2.8 lbs. \/ 1.27 kg.)","offer_id":48015756493115,"sku":"15944","price":46.99,"currency_code":"USD","in_stock":true},{"title":"Gallon Kit (11 lbs. \/ 4.99 kg.)","offer_id":48015756525883,"sku":"15961","price":138.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0780\/7539\/6411\/files\/epsilon-combo-533x400.jpg?v=1710988945","url":"https:\/\/maacaffestore.com\/products\/epsilon-101-fast-hardener","provider":"The Compleat Sculptor, Inc","version":"1.0","type":"link"}