{"product_id":"in-out-ii","title":"In \u0026 Out™ II","description":"\u003cp\u003e\u003cstrong\u003eIN \u0026amp; OUT™ II\u003c\/strong\u003e water soluble release agent will aid in releasing concrete or gypsum plaster castings from Smooth-On rubber molds. \u003cstrong\u003eIN \u0026amp; OUT™ II \u003c\/strong\u003eprovides a clean, positive release and does not interfere with or affect surface detail and helps minimize air bubbles in finished castings.\u003c\/p\u003e\n\u003cp\u003eFeatures\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eWill Not Stain \/ Soften Concrete Surfaces\u003c\/li\u003e\n\u003cli\u003eMix with Water - Economical\u003c\/li\u003e\n\u003cli\u003eWill Not Affect Color Pigmenting of Cast Concrete\u003c\/li\u003e\n\u003cli\u003eMinimizes “Bug Holes” In Concrete and Air Bubbles in Gypsum Castings\u003c\/li\u003e\n\u003cli\u003eKeeps Molds Clean - Does Not Build Up\u003c\/li\u003e\n\u003cli\u003eSignificantly Extends Mold Life\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eInstructions\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIN \u0026amp; OUT™ II IS DILUTED WITH WATER.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMeasuring \u0026amp; Mixing -\u003c\/strong\u003e Mix 4 parts water to 1 part In \u0026amp; Out II. Mixing can be done by hand or slow speed mixer. Do not shake or agitate as this may cause product to foam.\u003c\/p\u003e\n\u003cp\u003eHow you dilute \u003cstrong\u003eIN \u0026amp; OUT II™\u003c\/strong\u003e (amount mixed with water, coverage and frequency of application) will depend on the concrete aggregate mix and the form material you are casting into. For example, when casting concrete with a low grit\/high sand content (minimal abrasion) into a polyurethane mold, the mix ratio of water to \u003cstrong\u003eIN \u0026amp; OUT II™\u003c\/strong\u003e can be 4 : 1. High grit content may call for a dilution ratio of 2 parts water to 1 part release agent.\u003c\/p\u003e\n\u003cp\u003eMix only amount needed for one day. Mixture may separate after 24 hours. Re-mix to a uniform consistency and apply.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eApplication - \u003c\/strong\u003eApply \u003cstrong\u003eIN \u0026amp; OUT™ II \u003c\/strong\u003ethoroughly with brush, roller or spray. If pressure spraying, pressure should be 25 psi (172 kPa) or higher. For uniform spray applications of release agent, flat spray tips are suggested. Do not allow release agent to puddle.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCaution: Do Not Over Apply.\u003c\/strong\u003e Applying too much release agent will cause air bubbles “wormtracks”, “bugholes” or pitting on surfaces.\u003c\/p\u003e\n\u003cp\u003eBecause no two applications are quite the same, a small test application to determine suitability for your project is recommended if performance of this material is in question.\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.smooth-on.com\/msds\/files\/In_And_Out_II.pdf\" rel=\"noopener\" target=\"_blank\"\u003eSDS\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.smooth-on.com\/tb\/files\/IN_\u0026amp;_OUT_II_TB.pdf\" rel=\"noopener\" target=\"_blank\"\u003eTDS\u003c\/a\u003e\u003c\/p\u003e","brand":"Smooth-On","offers":[{"title":"8oz Trial Size (0.46 lbs. \/ 0.21 kg.)","offer_id":48015693775163,"sku":"66MR4","price":14.99,"currency_code":"USD","in_stock":true},{"title":"Gallon (7.4 lbs. \/ 3.36 kg.)","offer_id":48015693807931,"sku":"89661","price":78.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0780\/7539\/6411\/files\/inandout-ii-4gal-cs-hand-533x400-1.jpg?v=1713393553","url":"https:\/\/maacaffestore.com\/products\/in-out-ii","provider":"The Compleat Sculptor, Inc","version":"1.0","type":"link"}